Vana Ekipmanları, Aktüatörler ve Regülatörler – Fluscon

Pozisyon Transmitter

Mehmet Akın — Wed, 09 Nov 2022 14:29:43 +0000

SPECIFICATIONS

Type	Weatherproof/ Flameproof
Field Calibration	Auto calibration with stroke settings
Custom Set Point	21 freely configurable set points
Position Sensing	Contactless
Indication	LCD display – Current (mA) and Position (%)
Setup	Push button on device
Conduit Entry	½” NPT (F) or M20
Temperature	-20 °C to +60 °C (Standard) -40 C to +80 °C (On Request)

CHARACTERISTICS

Accuracy	0.3% of full scale
Repeatability	0.2% of full scale
Hysteresis	0.3% of full scale
Linearity	0.2% of full scale
Supply Voltage	24V DC + / – 10% (Loop Feedback)
Supply Connection	Screw Terminal (standard), M8 socket 3/4 pin (M) (optional)
Operating Range	3.6 – 21mA
Influence of Temperature	0.35% / 10 °K
Transmission Error	< 0.3%
Electromagnetic	CE, directive EMC 89 / 336 / EEC Compatibility

Elektro Pnömatik Pozisyoner

Mehmet Akın — Sun, 28 Aug 2022 08:30:18 +0000

Overview

TYPE	LINEAR		ROTARY
Operation	Single Acting	Double Acting	Single Acting	Double Acting
Supply Pressure	0.3 bar above actuator requirement (minimum 1.4 bar and maximum 7 bar)
Input Signal	4 to 20 mA DC constant current with maximum 30 VDC
Stroke	10-150 mm		0-90°
Air Connection	1/4″ BSP / NPT
Explosion Proof	ATEX
Protection	IP 66
Cam	Equal / Square / Square Root
Ambient Temperature	-40 °C to +120 °C, see ordering code
Linearity	± 1%	± 2%	± 1%	± 2%
Hysteresis	± 1%	± 1%	± 1%	± 1%
Sensitivity	± 0.2%	± 0.5%	± 0.5%	± 0.5%
Repeatability	± 0.5%	± 0.5%	± 0.5%	± 0.5%
Internal Bleeding	3 lpm (supply pressure 1.4 kgf / cm2), 11 lpm (supply pressure 4.0 kgf / cm2)
Flow Capacity	80 lpm (supply pressure 1.4 kgf / cm2), 200 lpm (supply pressure 4.0 kgf / cm2)
Material	Aluminium Die Casting
Weight	2.9 Kg	2.9 Kg	3 Kg	3 Kg

Smart Pozisyoner

Mehmet Akın — Sun, 28 Aug 2022 08:28:03 +0000

Overview
General	Loop powered, no external power supply required. External 24V DC option available. Blind mount Suitable for rotary and linear valves Actuator connections in accordance with VDI/VDE 3845 and IEC 60534-6 standards. Extensive selection of mounting kits for various kind of actuators
Action	Double or single acting
Failsafe	Failsafe or Stay-put (Fail freeze)
Actuator travel range
Linear	0 position can start anywhere, 3 to 200 mm stroke, other strokes on request
Rotary	0° can start anywhere, max. 359°
Measurement range	0 to 359° with freely rotating contactless feedback shaft.
Measurement range	0 to 300 seconds (configurable in incremental steps of 60 Seconds)e
Actuator travel limit	Freely configurable in 0% to 100%
Deadband time limit	0 to 300 seconds (freely configurable, monitoring parameter until deviations reaches within deadband)
Environmental Condition
Standard temperature range	-20 °C to +85 °C / -4 °F to +185 °F
Low temperature range	-40 °C to +85 °C / -40 °F to +185 °F -55 °C to +135 °C / -67 °F to 185 °F available on request
Influence of temperature on valve position	0.35% / 10 °K
Influence of vibration on valve position:	< 1 % under 10g 5–85 Hz, 2.5 85-150 Hz 1.5g 150–280 Hz, 0.5g 280–1500 H
Construction / Enclosure
Material*	1 = Epoxy coated anodised aluminium housing and Makrolon® (Polycarbonate) cover. 2 = Epoxy coated anodised aluminium housing and cover with Makrolon® see through window. 3 = Explosion proof aluminium housing and cover with Toughened Glass see through window. 4 = Explosion proof stainless steel housing and cover with Toughened Glass see through window. 5 = Intrinsically safe, epoxy coated anodised aluminium housing and Makrolon® (Polycarbonate) cover. 6 = Intrinsically safe, epoxy coated anodised aluminium housing and cover with Makrolon® (Polycarbonate) cover. 7 = Intrinsically safe, stainless steel housing and cover with Toughened Glass see through window.
Protection Class	Ip66
Pneumatic pressure ports	G1/4″ 1/4″ NPT
Exhaust Port	G1/4″ 1/4″ NPT
Cable Gland	½” NPT M20 x 1.5
Weight (with gauges)
Bare Positioner Option 1,5	2.25 kgs / 5 lbs
Bare Positioner Option 2,6	2.5 kgs / 5.5 lbs
Bare Positioner Option 3	6.6 kgs / 10.6 lbs
Bare Positioner Option 4,7	9.9 kgs / 21.9 lbs
Positioner Transmitter / Alarm Module	0.08 kgs / 0.2 lbs
Pneumatics
Supply pressure	1.4 to 8 bar / 0 to 114 psi (10 bar on request)
Capacity with 4 bar / 60 psi	> 1 to 41 Nm /h / 0.5 to 23 scfm (Servo controlled orifice)
Consumption with 4 bar / 60 psi (Steady State)	1 lpm / 0.037 scfm @ 4 bar

Damper Aktüatör

Mehmet Akın — Sun, 28 Aug 2022 08:23:22 +0000

Elektro Hidrolik Aktüatör

Mehmet Akın — Sun, 28 Aug 2022 08:19:18 +0000

TORQUE RANGE	Torque	25 to 6,00,000 Nm for rotary and 1.2 to 8000 kN force for linear actuator
ENCLOSURE PROTECTION	Construction	Casting: Cast Aluminium Actuator: Refer DRS Series Actuator Catalouge
	Ingress Protection	IP68 10m / 96h
	Controls location	As standard, the controls are integral to the actuator On option, the Controller can be mounted in a separated box (maximum distance between actuator and controls = 50m)
	Explosion proof ATEX	ATEX Directive 94/9/EC – CENELEC EN 60079-0, EN60079-1,EN13463 As standard: Ex d II B T4 (option T5 or T6) and Ex tb IIIC T135°C (option T100°C, T85°C) On request: Ex d II C T4 (option T5 or T6)
	Explosion proof IEC Ex	IEC Ex – standard IEC 60079-0, IEC60079-1, EN13463 As standard: Ex d II B T4 (option T5 or T6) and Ex tb IIIC T135°C (option T100°C, T85°C) On request: Ex d II C T4 (option T5 or T6)
	Ambient temperature operating range	IIB standard: -20 … +70°C IIB low temperature option: -60 … +70°C IIC option: -20 … +70°C
	External corrosion protection	Standard paint system: polyuréthane paint RAL3020 complying with ISO 12944 (C5) Optional special anti-corrosion protection for marine, aggressive or abrasive atmospheres All cover fasteners captive and stainless
	Double sealing Protection	The control section of the actuator is totally isolated from the terminal compartment to protect electronic components
MOTOR	Motor technology	Single & three-phase TENV type, totally enclosed non ventilated squirrel cage motors, Class F insulated with Integral thermal overload protection Class F insulated, DC motor with Integral thermal overload protection Easy to remove with sealed ball bearings fitted at front and rear
MOTOR	Motor duty rating	S4 motor service (intermittent service on start-up) to IEC 34-1 S4 – 30% for On/Off operation – up to 360 starts per hour S4 – 30% for Inching/Positioning – up to 360 starts per hour S4 – 50% for Modulating class III – up to 1,200 starts per hour
MECHANICAL SPECIFICATIONS	Manual override	Hydraulic Handpump
	Vibration Resistance	1g (9.8 m/s²) at 10-500 Hz (Contact our marketing dept. for higher vibration levels)
	Lubrication	Actuators are lubricated for product lifetime and do not require any specific periodic maintenance
ELECTRICAL SPECIFICATIONS	Power Supply	The actuators can operate on a wide variety of power supplies: Single-phase: 110, 120 & 230 V – 50/60 Hz Three-phase: 380, 400, 415, 440, 480, 575, 690 V – 50/60 Hz DC: 24V Voltage tolerance: ±10%; Applies for rated torque performance; duty cycle and speed is not guaranteed Frequency tolerance: ±5%; Applies for rated torque performance; duty cycle and speed is not guaranteed Maximum starting volt drop: -15%; Actuators capable of starting and running up to speed
	Cable Entries	Standard configuration: power & signal : 1”1/2 NPT + 2×1”NPT fieldbus : up to 4×3/4”NPT Other configurations available on request: plugs, adaptors, ISO thread
	Electrical connection	Ring tongue terminals Internal and external ground rod
	Fuse protection	Primary fuse (6.3 x 32mm – 0.5 A) located on the transformer board Two automatic fuses for low voltages
POSITION AND PRESSURE SENSORS	Position	C ontactless sensor Potentiometer (op tional)
POSITION AND PRESSURE SENSORS	Pressure	Pressure measured by piezoresistive pressure sensors based on ceramic
CONTROLS	Power circuit	Integral motor reversing starters (electromagnetic contactors for On-Off, Inching/Positioning, Modulating Class III)
	Display	Back-lit graphics display with a choice of 9 different languages
	On-off remote Control (Hardwired Control)	Command by voltage: 10 to 250 V DC/AC (current: 10 mA at 24V) dry contact (use Controller auxiliary 24 VDC supply) Isolated by opto-couplers Minimum pulse duration: 100ms
	Signaling relays	4 relays: each information can be freely selected Contact configuration : normally open or normally closed Minimum current 10mA at 5V Maximum current 5A at 250V AC or 5A at 30VDC (resistive load) Additional 3 relays board on option
	Fault relay	Normally closed & energized SPDT contact Minimum current 10mA at 5V Maximum current 5A at 250V AC or 5A at 30V DC (resistive load)
	Analogue Control	Input (setpoint) and output (feedback) signals are fully isolated from each other Signal configurations (selectable): Input signal: 4-20 mA – output signal: 4-20mA Input signal: 0-20 mA – output signal: 0-20mA Input signal: 0-10 V – output signal: 0-20mA (0-10V with an external resistance) Analogue inputs: in current: impedance of 160 Ohms in voltage: impedance of 11 KOhms Analogue outputs: in current: maximum acceptable load of 750 Ohms at 24 VDC supply In voltage: minimum acceptable load of 50 KOhms (with a shunt resistance of 500 Ohms)
	Transmitter (option)	Proportional position (0/4-20 mA) and Pressure (4-20 mA) feedback board
	Limit Switches	4 Mechanical Limit Switch (SPDT): 120/230 VAC or 30 VDC Proximity Limit Switch NO/NC (Optional): 5-60 VDC
	Signaling continuity (option)	Allows to use the display and update the open and closed position information (through the signaling relays or Profibus DP) in case of lack of power supply
	Fire protection (option)	30 minutes at 1,000°C Tested to UL 1709 criteria
SETTINGS	Settings	Non-Intrusive. All actuator settings and parameters are stored in a non-volatile EEPROM memory. Protection by password. Can be done by local command, infrared link or optional bluetooth link (For a good safety level, bluetooth link is limited at 10m)
	Local selectors	The Controller can be fully set via its local display and selectors Does not require any specific setting tool
	INTELLI+ KIT (option)	INTELLI+ SOFT CD-ROM for laptop PC Infrared module to connect to the laptop (USB) and clip on the actuator window From update 3.00, INTELLI+ SOFT is also able to manage bluetooth link with advanced torque recordings
	INTELLI+ Pocket (option)	Industrial pocket PC (PDA) Protection: IP65 (option: ATEX II2G EEx ia IICT4) Shock resistance: 1.2 m (on concrete) Communication: – with INTELLI+ : Infrared link (40 cm maximum distance) – with PC: bluetooth, IRDA, Wifi (802.11b) as a standard Optional USB station. Operating system: Windows Mobile 2005, 64Mb RAM + 256Mb storage card
FIELDBUS CONTROLS	Profibus DPV1 (option)	PROFIBUS-DPV1 – RS 485 Baud rate: 9.6 kbit/s up to 1.5 Mbit/s (autodetection) Communication protocol: PROFIBUS DPV1 slave-cyclic & acyclic Type of connection: single line (standard) or redundant line (option) Cable specification: Profibus certified cable only Line connection without repeater Actuators per line: 31 max Line length: 1.2 km max. (0.75 mi) Line connection with repeaters Number of repeaters per line: 9 max 30 actuators and 1 Km max. per segment Number of actuators per line with repeater: 124 maximum Line length with 9 repeaters: 10.2 km max. (6.2 mi) Scan speed (30 units & 1.2 km): 0.1s (at a baud rate of 93.75 Kbit/s) Power supply: internal and isolated via INTELLI+®. Optional signaling battery or 24VDC external backup supply update the open and closed position information in case of loss of power supply Technical approval: operability approved by PNO (Profibus Nutzer Organisation)
FIELDBUS CONTROLS	Modbus (option)	MODBUS RTU – RS 485 Transmission medium: 1 shielded pair cable Functions: Half Duplex, asynchronous mode, multidrop Baud rate: 1.2k to 115 Kbit/s Format: 8 data bits, 1 stop bit, no parity Communication protocol: Modbus (slave) Modbus address: configurable by the actuator menu
	Foundation Fieldbus (option)	H1 speed = 31.25kBit/s Fully compliant with fieldbus standard IEC 61158 Physical layer: IEC 61158-2, 2 wires communication Current consumption: 20mA Operating voltage: 9 to 32 VDC Cable specification: Type A (for example: 3076F Belden) Line connection Actuators per line without repeater: 31 max. Line length without repeater: 1.9 km max. (1.2 mi) Number of repeaters per line: 4 max. Maximum number of actuators and line length depends on consumption available Technical approval: Foundation tested. Several DCS manufacturer operability checked.
	Hart (option)	Interface: HART, 4-20mA current, FSK modulation Transfer speed: 1.2 kbit/s Protocol: HART 7.4 Impedance: 250 Ohms Power consumption: Internal by Intelli+ transformer, External power supply for 4-20mA loop only Actuator configuration: Available through EDD file Connection line: Point-to-Point or Multi-drop Technical approval: approved by Hart Communication Foundation

Pnömatik Aktüatör

Mehmet Akın — Sun, 28 Aug 2022 08:14:20 +0000

Elektrik Aktüatör

Mehmet Akın — Sat, 27 Aug 2022 15:07:37 +0000